How to repair or Reset Epson TX110 / TX111
Use the software resetter for Epson TX110 printer repair / TX111 (Adjustment program for Printer Epson TX110 / TX111)
 |
| Reset Epson TX110 / TX111 |
Get download Adjustment program for Printer Epson TX110 / TX111
Read More
Add your Comment
2
comments
Download Resetter Epson L200
Download Resetter Epson L200
 |
| Epson L200 |
Download Resetter Epson L200 or Adjustment Program for Epson L200
Read More
Add your Comment
0
comments
Error Code Canon MP150/MP160 and How to clear E27 Code MP150/MP160
 |
| MP150/MP160 |
E9 The connected digital camera / video camera does not support Camera
Direct Printing
E14 The Ink cartridges whose destination are wrong
E15 Ink cartridge is not installed E16 - Ink remaining is unknown
E16 -E19 Failed to scan head alignment sheet
E22 Carriage error
E23 Paper feed error
E24 Purge unit error
E25 ASF(cam) sensor error
E26 Internal temperature rise error
E27 Waste ink absorber full or platen waste ink absorber full
E28 Ink cartridge temperature rise error -
E29 EEPROM error
E33 Paper feed position error
E35 15 USB Host VBUD overcurrent error - USB
E37 17 Abnormal motor driver error
E40 20 Other hardware error
E42 22 Scanner error
How to clear E27 Code
- With the printer powered off but connected to a power source, press the Power button while pressing and holding the Stop/ Reset button.
- When the Power is lit, press the Stop/Reset button two times while pressing and holding the Power button.
- When releasing the Power button and the Stop / Reset button (regardless of order), the printer will move into a service mode. (Waiting for menu selection)
- When the on/off lights in green, press the Stop/Reset button the specified number of time(s) according to the function listed in the table below.(Each time the Stop/Reset button is pressed, the LED lights alternately in orange and green, starting with orange.)note: press 4 times for waste ink counter reset.
The number of the Reset button pressing LED Function Remarks
0 time Green Power off
1 time Orange Service pattern print (auto teste)
2 times Green EEPROM print (dados da EEPROM)
3 times Orange EEPROM reset (EEPROM reset)
4 times Green Waste ink counter reset (Absorvente reset)
- Turn off the printer.( it must be turn off) then turn it on again.
Read More
Add your Comment
1 comments
Repair or reset procedure for EPSON RX500
 |
| Repair or reset procedure for EPSON RX500 |
Protection counter is the counter for wasted ink; it says to printer how
much space it has in special tray where all wasted ink are going during
cleaning procedures. With time it became full (printer just won't print
in this case) and absorbtion padding must be replaced. After replacing
the padding You must reset the protection counter to zero in order to
continue ordinary printing.
Repair or reset procedure for EPSON RX500:
Press all following buttons :Power, Load/Eject, Stop, B&W, Color,
after this printer turns on and you'll see "Init eeprom" on printer screen.
Press Color button to clear protection counter.
Alternate. Hold down "clear + setup + on"
Continue to hold the buttons until the printer had powered on, then off again, then back on. Once you noticed that the LCD had flashed a blank screen, let go of the 3 keys. In the LCD window you now have access to 3 options using the select keys.
Look for an abbreviation resembling "ink pad level" . Here is where Held down the clear button for around 10 seconds. LCD must read "Press Power to Reset."
Repair or reset procedure for EPSON RX500:
Press all following buttons :Power, Load/Eject, Stop, B&W, Color,
after this printer turns on and you'll see "Init eeprom" on printer screen.
Press Color button to clear protection counter.
Alternate. Hold down "clear + setup + on"
Continue to hold the buttons until the printer had powered on, then off again, then back on. Once you noticed that the LCD had flashed a blank screen, let go of the 3 keys. In the LCD window you now have access to 3 options using the select keys.
Look for an abbreviation resembling "ink pad level" . Here is where Held down the clear button for around 10 seconds. LCD must read "Press Power to Reset."
Read More
Add your Comment
0
comments